Tools & Hardware

Jims 786 - 6-Speed Seal Installation Tool - '06-'16

Cruise Drive Main Case Seal Installer Harley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made JIMS® has developed a driver style seal installer (not a pushing or pulling type, which...

Jims 787 - Camshaft Bearing Installation Tool - '99-'17 Twin Cam

Cam Bearing Installation Tool Designed to press from the letter side of the inner cam bearing to eliminate any damage to the bearings, cam or case Will set bearings .023"-.028" below case surface Use to install the two inner cam bearings Made in the...

Jims 788 - Seal - Exhaust Gasket - Installer

Exhaust Gasket Seal Installer Tool Installs fragile exhaust seal with ease and will position seal evenly to exhaust port of head Can be used with exhaust flange nuts or JIMS handle sold separately Made in the U.S.A.

Jims 899 - Surface Temperature Strips - 30-Pack

Surface Temperature Indicating Strips Alerts you when metal has reached 210° F, the temp at which you should cease heating mainshaft, flywheel sprocket shaft, motor or transmission case when trying to remove stubborn bearings, races or gears Made in...

Jims 900 - Main Drive Gear/Bearing Remover/Installer - 6-Speed

Harley Davidson Cruise Drive 6-Speed Main Drive Gear and Bearing Remover/Installer Kit Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­® 6-speed transmission Tool removes and installs both parts...

Jims 901 - Main Drive Gear Remover Tool - Cruise Drive/6-Speed - Harley Davidson

Harley Davidson Cruise Drive 6-Speed Main Drive Gear Remover Tool Removes the main drive gear from the main bearing correctly while in the transmission case Eliminates the need of an arbor press and the risk of case damage

Jims 902 - Motor Stand - Blue - Twin Cam

Motor Stand Makes working on motors easier with better access Made in the USA

Jims 908 - Feeler Gauge - Set

Feeler Gauge Set Tool includes two gauge holders and the following size gauge inserts: .002", .003", .004", .005", .006", .008", .009", .010" and .011" New innovative feeler gauge holder cures the need to use bulky multi-feeler gauge tools while...

Jims 910 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 911 - Trap Door Bearing Remover/Installer - Cruise Drive/6-Speed - Harley Davidson

Harley Davidson Cruise Drive Trap Door Bearing Remover and Installer Accurately installs and removes lubed ball bearing into transmission trap door No arbor press needed Made in the U.S.A.

Jims 913 - Wheel Bearing Support Plate Tool

Late Model Wheel Bearing Tool Support Plate Provides accurate and precise bearing removal and installation without the risk of damage to cast wheels Attaches to the brake rotor mounting holes Works on 5 or 7 lug wheel Made in the U.S.A.

Jims 915 - Installation Inner Ball Bearing Tool

Balancer Inner Bearing Installer Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor press Designed for early or late Beta® cases Made in the U.S.A.

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to remove balancer inner bearings Protects left engine case...

Jims 917 - Clip - Pushrod Cover

Pushrod Cover Clip Will install and remove the clip professionally with just one hand in seconds This tool will NOT marr or slip Made in the U.S.A.

Jims 933 - Thread Chaser - SAE

Thread Chaser Tap Set An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted Includes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, and 9/16"-12 Not for cutting new threads Made in the U...

Jims 935 - Inspection Cutter Tool - Oil Filter

Oil Filter Cutter Use to inspect oil filter for any damaging particles that may be trapped in filter Locks down filter for a clean cut around filter base Fits filters up to 5-1/2" diameter Made in the U.S.A.

Jims 937 - Valve Guide Remover - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 938 - Valve Guide Installer - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 939 - Sealed Wheel Bearing Tool

Sealed Wheel Bearing Kit Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS) Made in the U.S.A.

Jims 941 - Oil Filter Tool - Slim

Slim Oil Filter Wrench An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust pipes, frame, hoses and brackets Simply the slimmest oil...

Jims 942 - Ignition Switch Connector Tool

Ignition Switch Connector Remover Slip the dog bone end of tool into the bottom side of connector until it is touching the back end of connector box Then gently pull out the male wiring connector and tool Safely removes ignition switch wiring...

Jims 943 - Ignition Switch Alignment Tool

Ignition Switch Housing Alignment Tools Also used to position switch in the correct orientation for properly activating the fork lock Proper alignment of the switch will extend the life of the ignition switch housing Align ignition switch housing as...

Jims 944 - Ignition Switch Alignment Tool

Ignition Switch Housing Alignment Tools Also used to position switch in the correct orientation for properly activating the fork lock Proper alignment of the switch will extend the life of the ignition switch housing Align ignition switch housing as...

Jims 94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.