Tools & Hardware

Jims 5517 - Shift Sleeve Tool - Big Twin

Shifter Mechanism Sleeve Tool A real time saver for removing and installing the shifter mechanism sleeve in Cruise Drive Big Twin transmissions Tool allows you to remove and install the sleeve (bushing) without having to disassemble the transmission ...

Jims 5518 - Shift Pedal Shaft Tool

Shifter Shaft Bushing Tool Time-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primary Tools installs new bushings to the correct location Made in the U.S.A.

Jims 5520 - Primary Locking Bar - XL

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in the U.S.A.

Jims 5530 - Fuel Tank - Remote

Remote Fuel Supply Tank For Fuel-injected Motorcycles Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a handlebar, be attached to a wall mount, work bench...

Jims 5532 - Tappet - Vacuum

Vacuum Tappet "Pump Up" Tool Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled Special jar, designed for vacuum, holds up to four hydraulic lifters in a...

Jims 5534 - Compensator Bolt Socket - Torx

Compensator Bolt Torx® Socket For the compensating sprocket retaining fastener Made in the U.S.A.

Jims 5800 - Flywheel Puller Tool - Indian

Flywheel Puller Tool Eliminates potential damage to the flywheel when used in this application Ensures good and solid engagement when using the puller Made in the U.S.A.

Jims 5803 - Wheel Bearing Hub Tool - Indian

Hub Protector Prevents damage to the wheel Made in the U.S.A.

Jims 5804 - Clutch Spring Compressor Adapter Tool

Clutch Spring Compressor Adapter An adapter for Jim's Clutch Spring Compressor Made in the U.S.A.

Jims 5805 - Wrist Pin Remover Tool - M8

Wrist Pin Adapter Quickly and easily removes wrist pins from Milwaukee-Eight® engines Adapter part for JIMS® Wrist Pin Tool (PART# DS-196197) Made in the U.S.A.

Jims 5806 - Camshaft Bearing - Remover/Installer Tool - M8

Milwaukee-Eight® Cam Bearing Tool The Milwaukee-Eight® engine returns to the single camshaft design, which requires a new tool for correct and accurate replacement of the camshaft inner needle bearing Uses the proven JIMS® style remover collet and fine...

Jims 5808 - Valve Spring Compression Collar Tool - M8

Valve Spring Collar Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made in the U.S.A.

Jims 5809 - Cylinder Hold Down Tool - M8

Cylinder Hold Down Nuts Useful when installing the second cylinder over the piston and rings after the first cylinder has been installed One end fits Twin Cam models, while the other end works with Milwaukee Eight® engines Keep the cylinders in place...

Jims 5810 - Main Seal Installer Tool - Left - M8

Main Seal Installer/Remover For use on Milwaukee Eight series engines

Jims 5811 - Balancer Scissor Gear Tool - M8

Alignment Screw Holds 2 halves of spring-loaded balancer scissor gear in alignment before removal Bright color reminds technician to remove it before sealing engine case For use on the Milwaukee Eight™ engine series

Jims 5812 - Rotor Alternator Tool - M8

Alternator Rotor Tool For use on the Milwaukee Eight™ engine series Removes rotor while protecting magnets Made in the U.S.A.

Jims 5813 - Main Bearing Remover and Installer Tool - M8

Main Bearing Remover and Installer Not only removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installation High levels of precision and accuracy are necessary, so only the best tools...

Jims 5813-5 - Stator Adapter Tool - M8

Milwaukee Eight® Stator Adapter Main Bearing Tool When this adapter is used in conjunction with the main bearing tool, or OE tool, the stator can remain attached to the left side case during bearing installation This adapter is a simple time and money...

Jims 5816 - Countershaft 1st Scissor Gear Alignment Tool - Cruise Drive

Countershaft 1st Scissor Gear Alignment Tool Essential for installing countershaft 1st scissor gear in cruise drive transmissions Ensures scissor gear teeth mesh correctly with the mainshaft 1st gear Maintains alignment of gear halves under spring...

Jims 5818 - Mount Wall - Fuel Tank

Fuel Tank Wall Mount Can be used on most one-piece fuel tanks that use 5/16" or 3/8" hardware to mount fuel tank to motorcycle frame Securely holds or displays fuel tank when mounted to wall stud Made in the U.S.A.

Jims 5820 - Installation Guide Tool - Standard - Rear Axle

Rear Axle Installation Guide Tool Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm) standard axles

Jims 5821 - Fork Cap Installer - 49 mm

Fork Cap Installer Used to install fork tube caps without removing the fork legs from the bike Made in the U.S.A.

Jims 5822 - Swing Arm Bearing Installer

Swingarm Bearing Installer Both drive side and brake side bearings, which are at different depths, can be easily and accurately installed with this tool kit JIMS® took it one step further and added a remover to press the spacer out of the bearing Made...

Jims 5823 - Flywheel Lock - Mighty Bite - Blue - M8

Mighty Bite Flywheel Lock Locks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engine Installs the case in place of the crank position sensor For use on the Milwaukee Eight™ engines