Tools & Hardware

Jims 34623-83 - Piston Pin Tool - Evolution

Piston Pin Keeper Tool This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible Use to install retaining ring in piston Made in the U.S.A.

Jims 34643-84 - Valve Seal Installer

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 34731-84 - Valve Guide Installer

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 34740-84 - Valve Guide Remover

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 34902-84 - Mainshaft Bearing Race Tool - Big Twin

Mainshaft Bearing Race Tool Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A.

Jims 34902-84-3 - Puller Plate Tool

Replacement Puller Plate Replacement puller plate for Jim's Mainshaft Bearing Race Tool for Big Twin models Made in the U.S.A.

Jims 35820-86 - Transmission Gear Spacing Tool - XL

Gear Spacing Tool Used to align main and countershafts when checking proper gear spacing Made in the U.S.A.

Jims 37047-91-5 - Sleeve - 2.060"

Sprocket Shaft Bearing Optional Sleeves For use on specific Harley-Davidson® Sportster and Buell® model years Optional sleeves for JIMS® Sprocket Shaft Bearing Installation Tool Both optional sleeves are required to install the sprocket bearing

Jims 37047-91-6 - Sleeve - 2.5"

Sprocket Shaft Bearing Optional Sleeves For use on specific Harley-Davidson® Sportster and Buell® model years Optional sleeves for JIMS® Sprocket Shaft Bearing Installation Tool Both optional sleeves are required to install the sprocket bearing

Jims 38515-90 - Clutch Spring Compressor

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and installed Made in the U.S.A.

Jims 38515-91 - Nut Clutch Spring Compressor XL

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and installed Made in the U.S.A.

Jims 39361-69 - Seal Installation Tool - Sprocket Shaft

Motor Sprocket Shaft Seal Install Tool Designed to press oil seal over sprocket shaft into case Made in the U.S.A.

Jims 5501 - Battery Lifter Tool

Battery Lifter Modeled after the larger tools made for automotive batteries, but is properly sized for Harley-Davidson® models Easily lifts batteries that have an extremely tight fit in the compartment Made in the U.S.A.

Jims 5502 - Ultimate Clutch Adjusting Tool

Ultimate Clutch Adjusting Tool Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or making multiple attempts to lock the nut and adjuster screw in the proper place ...

Jims 5503 - Master Kit - Front/Rear Brake/Clutch

Master Cylinder Hydraulic Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid...

Jims 5504 - Tappet Position Holder

Tappet Position Holding Tool Tappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engine Safely stores anti-rotation pins and tappets for proper and accurate installation Made...

Jims 5505 - Bike Wheel Lift Guide

Bike Lift Wheel Guide Helps to guide the front wheel track into the correct position on bike lifts Fits most bikes lifts with a front wheel vise Made in the U.S.A.

Jims 5506 - Magnetic Tappet Holder - Twin Cam and M8

Magnetic Tappet Holder Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while pushrods are tight The pushrod will spin with your fingers after the...

Jims 5507 - Lid Kit - Front Brake

Master Cylinder Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid used and a...

Jims 5508 - Lid Kit - Front Brake

Master Cylinder Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid used and a...

Jims 5509 - Lid Kit - Clutch Line

Master Cylinder Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid used and a...

Jims 5511 - Lid Kit - Rear Brake

Master Cylinder Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid used and a...

Jims 5515 - Neck Bearing Tool

Late-Model Neck Bearing Tool Tool has tapered drivers that ensure the correct installed alignment and depth of steering stem races Eliminates the risk of damaging the races and bearings during installation Made in the U.S.A.

Jims 5516 - Sprocket Nut Socket Tool - XL

XL Sprocket Nut Socket Tool Ensures the mainshaft on Harley-Davidson® Sportster models extend through the guidance collar for correct alignment Short socket is specifically designed to remove, install and properly tighten the front final drive sprocket...