Jims

Jims 2240 - Head Holder Guide Tool

Valve Guide Holder Kit Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide alignment shaft holds the right angle for best possible guide...

Jims 1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims 25586-37 - Cam Bushing - XL

Cam Cover Bushing Bushings are made from solid bronze bar stock Machined in one operation with a tolerance of .0002" Feature a lead-in for ease of installation Made in the U.S.A.

Jims 2244 - Fork Nut Socket - 35 mm - 3/8"

Top Nut Fork Socket Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A.

Jims 1047-TP - Crank Assembly Removal Tool - '55+ Big Twin

Crank Assembly Removing Tool This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will require a hard cap ...

Jims 95660-42 - 4-Speed Transmission Main Seal Tool - '36-'76 Big Twin

Big Twin Transmission Main Seal Tool Used to remove and install the main drive seal on specific Harley-Davidson® Big Twin models Made in the U.S.A.

Jims 97235-55B - Sprocket Shaft Bearing Nut Tool

Sprocket Shaft Bearing Nut Wrench Used to install and remove bearing nut Made in the U.S.A.

Jims 97272-60 - Camshaft Bearing Tool - Big Twin

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims 1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 95760-TB - Camshaft Bearing - Puller - Big Twin

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 35316-80 - Main Drive Gear Tool - 5-Speed

5-Speed Transmission Main Drive Gear Tool Installs the main drive gear without removing the transmission Used to remove and install the main drive gear Made in the USA

Jims 94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bushing Reaming Tool Use to ream rocker bushings to a factory fit of .0007” - .0012” in line with each other This precise line reamer is capable of a 24 finish or better Made in the U.S.A.

Jims 1283 - Camshaft Chain Tensioner Tool

Cam Chain Tensioner Tool Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain tensioners Comes with...

Jims 94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.

Jims 97273-60 - Camshaft Bearing Tool - XL

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims 96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 1743 - Swingarm Bushing Tool

Swingarm Bushing Tool Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of bushing Can be used with or without a press

Jims 35820-86 - Transmission Gear Spacing Tool - XL

Gear Spacing Tool Used to align main and countershafts when checking proper gear spacing Made in the U.S.A.

Jims 95960-52C - Clutch Hub Puller - '36-'90 Big Twin

Clutch Hub Puller Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A.

Jims 1041-TC - Camshaft Cover Holder Tool - '70-'99 Big Twin

Cam Cover Holding Tool Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U.S.A.

Jims 1030-TS - Socket - Crank Pin - Nut - Big Twin

Flywheel Socket Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A.

Jims 96780-58A - Piston Pin Lock Ring Tool - Big Twin

Piston Pin Lock Ring Tool Use to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like most aftermarket pistons This tool will install “spiral...

Jims 94660-37A - Center Shift Locknut

Transmission Sprocket Locknut Wrench Remove hex nut from end of main drive gear that secures the rear drive transmission pulley Inner collar will retain wrench to nut for safer work Extra-long...

Jims 95560-57 - Access Cover Tool - Transmission - Big Twin

Transmission Access Cover Puller Tool Use to remove transmission access covers, which are press-fit on two dowel pins Made in the U.S.A.