Jims

Jims 33288-37 - Kickstarter Bushing Kit - 4 Speed

Kickstarter Bushing Kit Made in the U.S.A.

Jims 1710 - Outer Race Snap Ring

Snap Ring Tool Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A.

Jims 24334-36 - Wrist Pin Bushing - Big Twin

Wrist Pin Bushing Machined from solid bronze bar stock Hold concentricity to less than .0002" Lead-in edge for easy installation Made in the U.S.A.

Jims 24600-58B - Crankcase Bushing

Right-Side Crankcase Bushing 360° oiling Made in the U.S.A.

Jims 2324 - Sprocket Shaft Installer

Sprocket Shaft Seal Installer Installs sprocket seal to proper depth Use with JIMS® Driver Handle Holds seal perfectly square Made in the U.S.A.

Jims 2188 - Camshaft Bearing Installer

Inner Cam Bearing Installation Tool Easily presses the inner cam bearing smoothly into the right case with the cases assembled to the proper depth Made in the U.S.A.

Jims 1052 - Oil Pump Snap Ring Installer

Oil Pump Snap Ring Installer Just apply oil to ring expander, slip ring up to the big end of ring expander, hold up to the end of the shaft, then push ring onto the shaft with sleeve Easily install...

Jims 95760-XL - Camshaft Bearing - Puller - XL

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 1726-2 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the...

Jims 2318 - Primary Locking Bar - XL

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1754 - Flow Pro 1 Billet Oil Pump Top Line - Polished

Flow Pro 1 Billet Oil Pump Complete Assembly CNC-machined feed and return gears increase pump flow and return volume Pumps include cover, gears, drive shaft, seals, gaskets, woodruff keys,...

Jims 1164 - Pistons Support Plate

Piston Support Plate Support plate gives a non-marring, flat surface to push piston bottoms against when installing rings or cylinders Made in the U.S.A.

Jims 1034 - Holder - Sprocket Shaft

Sprocket Shaft Holder Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A.

Jims 26328-74 - Feed Drive Oil Pump Gear - Big Twin

Oil Pump Component Oil Pump Component for Big Twin models

Jims 24002-70 - Sprocket Shaft Oil Seal Spacer

Motor Sprocket Shaft Spacer Machined to a 32-micron, burr-free finish for extended seal life Made in the U.S.A.

Jims 1147 - Alternator Rotor Puller

Alternator Rotor Tool A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft from...

Jims 26346-69/70 - Oil Pump Shaft - Big Twin

Oil Pump Component Oil Pump Component for Big Twin models

Jims 18534-29A - Tappet Roller - Big Twin

Tappet Roller Kit Made from 52100 bearing material Includes 4340 chromoly axle Made in the U.S.A.

Jims 2189 - Transmission Shaft Installer

Transmission Shaft Installer Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A.

Jims 2046 - Fork Seal Installer - 39 mm

Fork Seal and Cap Installer Lightly grease to keep from scratching fork tubes Used to install fork and dust seals Made in the U.S.A.

Jims 1146 - Crankshaft Bearing Installer - Twin Cam

Twin Cam "B" Motor Crankshaft Bearing Tool Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A.

Jims 34761-84 - Clutch Spring Tool - XL '84-'90

Clutch Spring Tool Use to release the clutch spring tension for disassembly Made in the U.S.A.

Jims 3998K - Wrist Pin Bushing - Twin Cam

Wrist Pin Bushing Machined from solid bronze bar stock Hold concentricity to less than .0002" Lead-in edge for easy installation Made in the U.S.A.

Jims 2237 - Pinion Gear Lock Tool

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.