Jims

Jims 966 - Starter Seal Tool

Starter Jackshaft Seal Installer Tool Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner primary of Big Twins Made in the...

Jims 2312 - Primary Locking Bar Tool

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 963 - Bearing Puller Tool - '03-'17 Twin Cam

Bearing and Race Puller Tool Can also be used to remove Timken® bearing pinion shaft inner bearing race on '57-'07 XL, including all Buells®, and used to remove press-fit transmission gears and...

Jims 956 - Sleeve Kit

Replacement Sleeve Kit Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool

Jims 969 - O² Sensor Tool - Socket

O² Sensor Tool Remove and install oxygen sensors on fuel-injected models Socket tool will withstand up to 125 ft.-lbs. of torque Made in the USA

Jims 1075 - Installer - Cylinder Stud

Evolution Cylinder Stud Assembly Tool Assembly tool features a captive hardened ball bearing dimensionally set 1" from top of tool Works on all Evolution Big Twin and XL models Made in the U.S.A.

Jims 995 - Splitter Case - '07-'17 Twin Cam

Case Splitter Tool "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary mounting...

Jims 1666 - Crank Lock Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 975 - Rotator Tool - Engine - Twin Cam

Engine Rotator Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and checking operating clearances...

Jims 994 - Camshaft Locking Tool - Big Twin

Sprocket Lock Tool Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts Comes with instructions Made in the U.S.A.

Jims 1042-8 - Wheel Bearing Puller Tool - 25 mm

25 mm Wheel Bearing Tool For use with 25 mm wheel bearing found on '07-'19 Harley-Davidson® models Made in the U.S.A.

Jims 972 - Gear Seal Installer - Main Drive - 6-Speed

Driver Handle Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be used to protect main drive gear inner...

Jims 959 - Case Bearing Tool - Conversion - Twin Cam

Timken® Case Bearing Tool Kit Includes one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate...

Jims 960 - Balance Shaft Tool - Softail

Balancer Shaft Removal Tool Removes both the front and rear counter-balancer shaft bearing assembly, from the left engine case Designed for the 96" and 110" Beta® engines Made in the U.S.A.

Jims 957 - Shaft Bearing Remover/Installer Tool - Balancer

Outer Balancer Bearing Tool Also installs the new balancer bearing and counter balancer shaft on Twin Cam 96", 103" or 110" "B" Softail engines Complete kit safely removes and installs outer...

Jims 990 - Camshaft Assembly Tool - '07-'17 Twin Cam

Cam Assembly Tool Holds both cams in an upright position while lowering cam support plate over both guides and cam journal guides Made from a non-marring material that will not damage any of the...

Jims 967 - Inner Primary Bearing/Seal Tool - Installation/Removal - Kit

Inner Primary Bearing and Seal Remover/Installer Tool — Removal/Installation Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of...

Jims 976 - Rotator Tool - Engine - Big Twin

Engine Rotator Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and checking operating clearances...

Jims 973 - Sprocket Bearing Installer Tool

Bearing Adapter Allows installation of shaft bearing on '06 Harley-Davidson® Dyna Glide and all '07-'17 Twin Cam models An adapter for JIMS® Sprocket Shaft Bearing Tool

Jims 5480 - Coil Relocation Kit - M8 Softail

Coil Relocation Kit Re-position and mount the coil below the neck and in-between the frame down tubes on the front of the bike Includes all necessary mounting hardware along with extended spark...

Jims 5470 - Forceflow Cylinder Head Cooler Kit - Black - M8 Softail

Forceflow Cylinder Head Cooler Kit Includes Forceflow assembly with high-powered fan, OEM-type replacement horn, temperature switch, manual override switch, wiring, hardware and complete...

Jims 5468 - Forceflow Cylinder Head Cooler Kit - Black - M8 Touring

Forceflow Cylinder Head Cooler Kit Includes Forceflow assembly with high-powered fan, OEM-type replacement horn, temperature switch, manual override switch, wiring, hardware and complete...

Jims 5401 - Forceflow Cylinder Head Cooler Kit - Black - Twin Cam Touring

Forceflow Cylinder Head Cooler Kit Includes Forceflow assembly with high-powered fan, OEM-type replacement horn, temperature switch, manual override switch, wiring, hardware and complete...