Jims

Jims 1236 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 5806 - Camshaft Bearing - Remover/Installer Tool - M8

Milwaukee-Eight® Cam Bearing Tool The Milwaukee-Eight® engine returns to the single camshaft design, which requires a new tool for correct and accurate replacement of the camshaft inner needle...

Jims 5812 - Rotor Alternator Tool - M8

Alternator Rotor Tool For use on the Milwaukee Eight™ engine series Removes rotor while protecting magnets Made in the U.S.A.

Jims 5810 - Main Seal Installer Tool - Left - M8

Main Seal Installer/Remover For use on Milwaukee Eight series engines

Jims 5826 - Stand - Engine - M8

Engine Stand For use on the Milwaukee Eight™ engine series JIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail engines JIMS Milwaukee-Eight® Softail®...

Jims 5829 - Cylinder Torque Plates - M8

Cylinder Torque Plate Kit Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims 5833 - Ball Bearing Installation Tool - M8

Balancer Bearing Installer All Milwaukee-Eight® (M8) engines incorporate balancers to reduce vibration Designed to precisely install these bearings in the proper location for all M8 engines This...

Jims 5811 - Balancer Scissor Gear Tool - M8

Alignment Screw Holds 2 halves of spring-loaded balancer scissor gear in alignment before removal Bright color reminds technician to remove it before sealing engine case For use on the Milwaukee...

Jims 5800 - Flywheel Puller Tool - Indian

Flywheel Puller Tool Eliminates potential damage to the flywheel when used in this application Ensures good and solid engagement when using the puller Made in the U.S.A.

Jims 5813 - Main Bearing Remover and Installer Tool - M8

Main Bearing Remover and Installer Not only removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installation High levels of...

Jims 5830 - Main Seal Remover Tool - Left

Main Seal Installer/Remover For use on Milwaukee Eight series engines

Jims 5808 - Valve Spring Compression Collar Tool - M8

Valve Spring Collar Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made in the U.S.A.

Jims 5828 - Cylinder Head Holder Tool - M8

Two-Sided Head Holder Tool Allows you to easily position head for all types of work Use to hold head in vice through spark plug hole For use with Milwaukee Eight engine series Has 14 mm and 12 mm...

Jims 1042-7 - Expander Dowel Tool

Bearing Expander Rod Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims 1278-3 - Camshaft Bearing Installation

Replacement Drive Replacement drive for JIMS® Cam Bearing Installation Tool

Jims 952 - Balancer Shift Alignment Tool

Balancer Shaft Sprocket Alignment Tool Takes the guesswork out of setting up your balancer shaft sprocket and chain alignment Made in the U.S.A.

Jims 2240-11-4 - Adapter - Valve Guide - Insert - 7 mm

Valve Guide Adapter Adapters are supported by a stand that makes it easy to press valve guides in and out Adapters for working on 7 mm valve guides Made in the U.S.A.

Jims 780 - Tester Tool - Seal Leak

Interconnect Seal Leak Testing Tool Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases horsepower...

Jims 1090 - Tester - Valve Spring

Mini Valve Spring Tester Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter Works with bench vise, arbor, screw hydraulic or drill press 0 to 1000 P.S.I...

Jims 915 - Installation Inner Ball Bearing Tool

Balancer Inner Bearing Installer Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor press Designed for early...

Jims 902 - Motor Stand - Blue - Twin Cam

Motor Stand Makes working on motors easier with better access Made in the USA

Jims 933 - Thread Chaser - SAE

Thread Chaser Tap Set An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted Includes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13,...

Jims 937 - Valve Guide Remover - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 786 - 6-Speed Seal Installation Tool - '06-'16

Cruise Drive Main Case Seal Installer Harley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made JIMS® has developed a driver...